ENGLAND
(-)*+
AAAAA
1Clutch lever6Hoeing blades11 Spark plug16Oil-filter cap for engine
2Handles7Filter cap for gearbox12 Engine start grip17 Oil-drain plug for engine
3START/STOP switch8Drain plug for gearbox13 Tank18 Accelerator
4Skid9Reduction gear14 Motor
5Protection guard10 Transport wheels15 Handle plate
(-)*+
BBBBB
ASSEMBLY OF: HANDLES - SKID - WHEEL - ACCELERATOR LEVER - OFF-SWITCH.
Handles (2): mount handle-plate (15) in the frame (19) and fix it with four screws, washers and nuts (20). Now introduce the two handles (2) into the handle-plate and
fix them with screws, washers and wing screws(21).
Skid (4): indroduced the skid into the seat an the frame (19) and fix with cotter pin (22).
Wheel (10): Mount the wheel rod (23) an the frame (19) and then fix with screw, washer and nut (24). Introduce cotter pin (25).
Accelerator lever (Governor) (18): (this refers only to the version with 4-stroke engine). Fix the governor to the handles (2) by means of screw and nut (26).
Switch (3): (this refers anly to the version with 2-stroke engine). Introduce the terminals of grounding cables (32) into the fixing spots of the switch.
(-)*+
CCCCCBefore you start working, make sure to remove any objects or obstacles that may have been left on the lawn. The operator is responsible for the safety of other people in
the working area.
(-)*+
ENIGNE SET UP
DDDDDFor the setting of the engine, it is necessary to follow the instructions given in the engine maintenance manual issued by the manufacturer of the engine.
(-),+
EEEEEENGINE STARTUP
CAUTION:- 0.6l Oil must be added to the engine before use.
Once the machine has been set up properly, start the engine as follows:
1) 2-stroke engine version, position the switch (3) on START to enable engine startup.
1.a) Grip the starting handle (12) and pull the engine start grip gently until you feel the resistance caused by compression. Release the handle; then give the starter rope a
sharp tug.
(-),+
FFFFF2) 4-stroke engine version:
2.a)Engines with choke system:
if the model is equipped with an accelerator, when the engine is cold, position the accelerator lever (18) on START
2.b)Engines with primer system:
Press the fuel-enrichment pump located on the carburettor 3 or 4 times, if the model is equipped with an accelerator, position the accelerator lever (18) on MAX.
2.c) Grip the starting handle (12) and pull the starter rope gently until you feel the resistance caused by compression. Release the handle; then give the starter rope a sharp
tug.
For further information and explanation, read carefully the Engine Manufacturers instruction manual.
(-),+
GGGGGBefore starting work, it is necessary to carry out the following:
-adjust the skid (4) according to the soil and the depth of hoe which is required, to do this insert the cotter pin (22) in one of the holes on the skid and fix it with
clip.
- set the trasport wheels (10) upwards. For this purpose move the wheel rod (23) in the upper hole and fix it with cotter pin (25).
WHEN THE ENGINE IS ON: in order to make the tiller blades (6) run, handle (1) must be depressed. When working with the tiller, keep the handle depressed. If the handle
is released, the hoeing blades will come to a "stop"
Depress the skid in order to work in depth and decrease the pressure to move forwards.
HOW TO STOP THE ENGINE:
- 2-stroke engine version, set the interrup button to STOP.
- 4 stroke engine version, set accelerator lever to STOP.
HOW TO MOUNT THE HOEING BLADES (6): mount the hoeing blades an the rotary shaft (27) and make two holes (28) coincide, then fit pin (29) and fix with the
respective spring.
7 |