Front panel facilities
Front panelDigital format:
The current input source is set for
Powera digital format of OAuto.�
Bass level:After plugging in the power cord into the rear panel and
wall outlet, pressing this button connects the DTR-9.1 to
the AC mains and turns it on.
The current bass level is +2.
Y Before turning on the power, make sure all cables are
properly connected.
Treble level:
Y Turning on the DTR-9.1 may cause a momentary power
surge that might interfere with other electrical equip-
The current treble level is -2.ment on the same circuit. If this is a problem, plug the
DTR-9.1 into a different electrical circuit.
Input Source Buttons (DVD, VIDEO 1�5, TAPEStandby/On
1�2, AM, FM, PHONO, and CD) and Indicator
Pressing this button while the main power is turned on the
These buttons are used to select the input source for the
STANDBY indicator lights up and the front display turns off.
main zone. When an input source is selected, the indica-Pressing it again returns it to the standby state. This state
tor will light in orange. To select the input source for theturns off the display, disables control functions, and turns
remote zone (Zone 2) or recording out (Rec Out), first press
off all outputs to the main zone (those for the remote zone
the Zone 2 or Rec Out button, and then the desired inputremain available).
source button.
Standby indicator
Zone 2/Rec Indicator
For Zone 2, the indicator above the selected input
Master Volumesource button will light green. For recording, it will light
The MASTER VOLUME knob is used to control the volumered.
for the main zone. The volume for the remote zone (Zone
2) is independent.
Front panel door
Open/CloseCaution:
The front door of the receiver is motorized. Use the open/
Press this button to open and close the front door that
close button to open or close the door. Manually openingcovers the lower buttons.
or closing the door, or moving the receiver while holding
the door, will cause the door to malfunction or break.
Display
Rec OutThe DISPLAY button is used to display information about
the current input source signal. Each time you press the
Press the Rec Out button to output to a recording compo-display button, the screen changes to show you different
nent for recording purposes. After pressing the Rec Out
information concerning the input signal.
button, press one of the input source selector buttonsThe screen changes as follows:
within 8 seconds to select the component to record to.
When one is selected, the indicator above that button willProgram format ? Sampling frequency ? Digital input ?
Digital format ? Bass level ? Treble level.
light in red. To record from the same input source that youIf the input source signal does not have any information
are using (that is selected for the main zone), press the
for a particular screen, then that screen will be skipped.
Rec Out button twice in succession.
Y Displaying the data of the current input source
Note:Each display is explained below.
The Rec Out and Zone 2 buttons use the same circuit and
therefore cannot be used at the same time.
LFE(Low Frequency Effect)When Rec Out is selected, nothing is output from Zone 2.
Program
format:Zone 2
The DTR-9.1 includes a second signal path separate from
Front channel Surround channelthe main one that can be used for a remote zone (Zone 2)
or for making recordings. By connecting an additional
amplifier or other video equipment to the Zone 2 outputs,Source signal48 kHz
you can output to a separate room an input source that is
Samplingdifferent from that being used in the main room. This al-
frequency:lows you to watch one program in one room while some-
body else is watching a different program in another.
Sampling frequencyPress the Zone 2 button to enable output to the ZONE 2
outputs. After pressing the Zone 2 button, press one of the
input source selector buttons within 8 seconds to select
the input source for the remote zone. When one is se-Digital input:
lected, the indicator above that button will light in green.
The current input source is set for
digital input at OPT1.
9 |
ACEC
