G per mezzo della vite a corredo. (fig. 4).
Montare il deflettore G in modo che i fumi
Ivengano convogliati verso la parte opposta
al muro retrostante, cos? facendo si eviter?
DESCRIZIONE DELLA CAPPAche i fumi di scarico sporchino il muro.
Fissare il deflettore alla cappa tramite la vite
1) Tasto velocit? motorea corredo.
2) Tasto luce
3) Cassetto estraibileINSTALLAZIONE
4) Griglie dOaspirazioneLOapparecchio messo in opera dovr? distare
5) Illuminazione piano di lavorodal piano di lavoro non meno di cm. 43 nel
caso di fornelli elettrici e cm. 65 nel caso di
UTILIZZAZIONEfornelli a gas o misti.
Sono possibili le seguenti utilizzazioni dellaCollegamento elettrico
cappa:Prima di effettuare qualsiasi collegamento
N Versione ad evacuazione esternaassicurarsi che la tensione di rete corrispon-
(aspirante)da, alla tensione riportata sullOetichetta ca-
N Versione a riciclo (filtrante)ratteristiche situate allOinterno dellOapparec-
chio.
Versione ad evacuazione esternaLOapparecchio Ź fornito di una spina regola-
(aspirante)mentare; allacciarlo ad una presa conforme
LOaria viene espulsa allOesterno con lOausilioalle norme vigenti.
di un tubo ? 120mm da collegare allO anelloSe si intende collegare la cappa permanen-
di raccordo A ( fig. 1).temente alla rete elettrica, dopo aver rimos-
L'anello di raccordo Ź provvisto di una valvo-so la spina, Ź obbligatorio installare un inter-
la non ritorno fumi.ruttore bipolare a norme con una distanza
Nei tratti orizzontali il tubo deve avere unadei contatti in apertura non inferiore a 3 mm.
leggera inclinazione (10% circa) verso lOaltoSi declina ogni responsabilit? per inconve-
per convogliare agevolmente lOaria allOester-nienti derivati dallOinosservanza della sud-
no dellOambiente.detta disposizione.
Versione a riciclo (filtrante)Fissaggio della cappa al pensile
LOaria viene filtrata attraverso un filtro alApplicare la dima di foratura a corredo N94
carbone (Typ 150) e riciclata nellOambiente.sul fianco del pensile di destra.
Se la cappa Ź sprovvista di filtro, richiederloEseguire almeno 2 fori del diametro di 2 mm
al servizio assistenza tecnica specificando ilnei punti 1-2-3 (fig. 5).
modello dellOapparecchio.Eseguire le stesse operazioni sul fianco del
Per montare il filtro procedere come segue:pensile di sinistra.
Estrarre completamente il cassetto estraibi-Fissare la cappa ai pensili per mezzo delle
le della cappa.viti H fornite a corredo (fig. 5).
Per togliere il filtro metallico premere con-Se si dispone di un solo pensile laterale, la
temporaneamente le due maniglie M versocappa deve essere prima fissata anche al
l'alto (Fig. 2-1) e successivamente spostaremuro.
le stesse verso l'interno (Fig. 2-2).Fissare le 2 attaccaglie I sul lato supe-
Inserire il filtro a carbone nella sede e fissar-riore della cappa tramite le 4 viti a cor-
lo per mezzo dei due agganci F (fig. 3). LOariaredo (Fig. 6).
filtrata viene scaricata sopra il pensile. SulFissare i ganci L al muro tramite i tas-
foro di uscita deve essere fissato il deflettoreselli ?8mm e le viti 5x45 fornite a corre-
do (Fig. 5).
11 |