DVP-NS775V/NS780V
REARREAR (10 ft)Set this within -16 and
NotesAdjusting the speaker volume
LARGE(REAR/SIDE): Normally select The cut off frequency for the subwoofer is fixed at and level+2ft of the ?FRONT?
this position. Select according 120 Hz.setting in 1 ft increments.
to the rear speaker position*. If your speakers are too small to reproduce low is set to 17 ft, ?REAR? can 1Select SPEAKER SETUP in the Setup For example, if ?FRONT?
SMALL(REAR/SIDE): Select this bass frequencies, utilize a subwoofer for low be set between 1 and 19ft.Display.
when the sound distorts or the frequency sound. When you set the speaker
surround effects are difficult to settings to ?SMALL,? the bass redirection 2Select TEST TONE and set to ON.Ž
hear. Select according to the circuitry will be activated and the bass NoteYou will hear the test tone from each
rear speaker position*.frequencies for the speakers are output from the If each of the front or rear speakers are not placed at speaker in sequence.
subwoofer.
NONESelect this if you do not connect Even if there are fewer than 6 speakers connected, an equal distance from your listening position, set 3From your listening position, select
rear speakers.the player distributes the audio signal components the distance according to the closest speaker.
LEVEL (FRONT) or LEVEL (REAR)
to the front speakers.ALEVEL (FRONT)
*Rear speaker positionand adjust the value using X/x.
Correctly specify the location of the rear speakers to ADISTANCEVaries the level of the front speakers. Be sure The test tone is emitted from both left and
enjoy the surround effect.Sets the distance from your listening position to set ?TEST TONE? to ?ON? for easy right speakers simultaneously.
Set to ?SIDE,? if the location of the rear speakers to the speakers. adjustment.
corresponds to section A below.Set the distance to your front speakers in The default adjustments are in parentheses.4Select TEST TONE and set to OFF
Set to ?REAR,? if the location of the rear speakers ?FRONT? first (A). Then adjust the values in to turn off the test tone.
corresponds to section B below.?CENTER? (center speaker B), and L (0 dB)Set this between -6 dB and 0
This setting affects only ?VIRTUAL REAR ?REAR? (rear speaker C) to reflect the dB in 0.5 dB increments.
SHIFT,? ?VIRTUAL MULTI REAR,? and R (0 dB)Set this between -6 dB and 0
?VIRTUAL MULTI DIMENSION? mode actual distance to your center speaker, and NotedB in 0.5 dB increments.
(page54). This setting does not affect the Super rear speakers.The test tone signals are not output from the digital
Audio CD Multi audio signals.CENTER Set this between -12 dB and jack.
(0 dB)0 dB in 0.5 dB increments.
BSUBWOOFER Set this between -15 dB and
(-5 dB)+5 dB in 0.5 dB increments.
AAALEVEL (REAR)
(4~50 ft)(4~50 ft)Settings and AdjustmentsVaries the level of the rear speakers. Be sure
to set ?TEST TONE? to ?ON? for easy
90 adjustment.
45 The default adjustments are in parentheses.
CCL (0 dB)Set this between -12 dB and
20 0 dB in 0.5 dB increments.
R (0 dB)Set this between -12 dB and
SUBWOOFER0 dB in 0.5 dB increments.
YESSelect this if you connect a
Be sure to change the value in the Setup subwoofer to output the LFE To adjust the volume of all the speakers at
(Low Frequency Effect) signals Display each time you move the speakers. one time
from the subwoofer.Start from the front speaker. The default Use the amplifier?s (receiver?s) volume
adjustments are in parentheses.control.
NONESelect this if you do not connect
a subwoofer.FRONT Set this between 4 and 50 ft ATEST TONE
(10 ft)in 1 ft increments.
The speakers will emit a test tone. Use this
CENTER (10 ft) Set this within -5 and +2ft when you use the 5.1CH OUTPUT jacks and
of the ?FRONT? setting in adjust ?LEVEL (FRONT)? and ?LEVEL
1 ft increments. For (REAR).?
example, if ?FRONT? is set
to 17 ft, ?CENTER? can be OFFThe test tone is not emitted
set between 12 and 19 ft.from the speakers.
ONThe test tone is emitted from
each speaker in sequence while
adjusting level.
,continued8384
, Even if your TV is compatible with , The MP3 audio track does not have the
The sound volume is low.
progressive format 480p signals, the image extension ?.MP3.?
Additional Informationmay be affected when you set the player to , The sound volume is low on some DVDs. The sound volume may improve if you set , The data is not formatted in MP3 even
progressive format. In this case, select though it has the extension ?.MP3.?
?AUDIO DRC? in ?AUDIO SETUP? to
?NORMAL (INTERLACE)? using the , The data is not MPEG1 Audio Layer 3 data.
TroubleshootingPROGRESSIVE button on the front panel ?TV MODE? (page80)., The player cannot play audio tracks in
so that the PROGRESSIVE indicator turns , Set ?AUDIO ATT? in ?AUDIO SETUP? to MP3PRO format.
off and the player is set to normal (interlace) ?OFF? (page80)., ?MODE (MP3, JPEG)? is set to ?IMAGE
If you experience any of the following
difficulties while using the player, use this format.(JPEG)? (page66).
troubleshooting guide to help remedy the The surround effect is difficult to hear
problem before requesting repairs. Should The picture does not fill the screen, even when you are playing a Dolby Digital, or The JPEG image file cannot be played
any problem persist, consult your nearest though the aspect ratio is set in TV TYPE DTS sound track.(page62).
Sony dealer (For customers in the USA only).under SCREEN SETUP.Ž, Check the speaker connections and setting , The DATA CD is not recorded in a JPEG
(page28, 30, 81).
, The aspect ratio of the disc is fixed on your format that conforms to ISO 9660 Level 1/
PowerDVD., The 5.1 channel sound is not recorded on Level 2, or Joliet.
the disc being played., The file has an extension other than
The power is not turned on.?.JPEG? or ?.JPG.?
Sound
, Check that the power cord is connected The sound comes from the center speaker , The image is larger than 3072 (width) u
securely.There is no sound.only.2048 (height) in normal mode, or more than
, Re-connect the connecting cord securely., Depending on the disc, the sound may come 3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
Picture, The connecting cord is damaged.from the center speaker only.
, The player is connected to the wrong input , Set the surround mode setting to ?OFF? displayed even if the file size is within this
There is no picture/picture noise appears.jack on the amplifier (receiver) (page26, (page53).specified capacity.)
, The image does not fit the screen (the image
, Re-connect the connecting cord securely.27, 28).
, The connecting cords are damaged., The amplifier (receiver) input is not is reduced).
Operation
, Check the connection to your TV (page19) correctly set., ?MODE (MP3, JPEG)? is set to ?AUDIO
(MP3)? (page66).
and switch the input selector on your TV so , The player is in pause mode or in Slow-The remote does not function.
that the signal from the player appears on motion Play mode., The batteries in the remote are weak.
the TV screen., The player is in fast forward or fast reverse , There are obstacles between the remote and The MP3 audio tracks and JPEG image
, The disc is dirty or flawed.mode.the player.files start playing simultaneously.
, If the picture output from your player goes , If the audio signal does not come through , The distance between the remote and the , ?MODE (MP3, JPEG)? is set to ?AUTO.?
through your VCR to get to your TV or if the DIGITAL OUT (OPTICAL or
you are connected to a combination TV/COAXIAL) jack, check the audio settings Additional Informationplayer is too far., The remote is not pointed at the remote (page66).
VIDEO player, the copy-protection signal (page81).sensor on the player.
applied to some DVD programs could affect , Super Audio CD audio signals are not The album/track/file names are not
picture quality. If you still experience output from the DIGITAL OUT (OPTICAL displayed correctly.
problems even when you connect your or COAXIAL) jack.The disc does not play., The player can only display numbers and
player directly to your TV, try connecting , While playing a Super VCD on which the , The disc is turned over.alphabet. Other characters are displayed as
your player to your TV?s S VIDEO input audio track 2 is not recorded, no sound will Insert the disc with the playback side facing ?*?.
(page19).come out when you select ?2:STEREO,? down.
, You have selected ?PROGRESSIVE ?2:1/L,? or ?2:2/R.?, The disc is skewed.
(AUTO)? or ?PROGRESSIVE (VIDEO)? , The player cannot play certain discs The disc does not start playing from the
using the PROGRESSIVE button on the Sound distortion occurs.(page9).beginning.
front panel (the PROGRESSIVE indicator , The region code on the DVD does not match , Program Play, Shuffle Play, Repeat Play, or
lights up) even though your TV cannot , Set ?AUDIO ATT? in ?AUDIO SETUP? to the player.A-B Repeat Play is selected (page40).
?ON? (page80).
accept the progressive signal. In this case, , Moisture has condensed inside the player , Resume play has taken effect (page36).
select ?NORMAL (INTERLACE)? so that (page5).
the PROGRESSIVE indicator turns off., The player cannot play a recorded disc that The player starts playing the disc
is not correctly finalized (page9).
automatically.
, The disc features an auto playback function.
The MP3 audio track cannot be played , ?AUTO PLAY? in ?CUSTOM SETUP? is
(page62).set to ?ON? (page79).
, The DATA CD is not recorded in an MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
,continued8586
1-20 |
ACEC
