SONY DMBK-R3006 Repair Manual

$7.99

SONY DMBK-R3006 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Wednesday 21 November, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Grace Towers - 05/22/2008

Very nice clear manual with specifications, exploded views and schematics, been searching for one of these for years. Thanks.

HIROSHI EMOTO - 11/29/2007

Very fast service and a good documents. Thank you.

Anny ROY - 04/06/2007

Super fast service and document of excellent quality. Thanks

Gaspar Lovas - 11/03/2009

That's all right, thank you for all your trouble. Yours sincerely GL

Henry Seiden - 02/26/2009

I downloaded this product and looked through it quickly with Adobe Reader v9. It is clean and a good copy. Some scanned pages are not perfectly square, but that is a minor complaint. The document schematics and board diagrams are easy to read, of good contrast. The whole file downloaded quickly. This is a good service! Sony charges about $100 for the printed version of the same manual. It is still available through their print-on-demand pro parts system, but why would you do that?

Customers who bought this product also purchased

SONY AC-E60A Owner's Manual	SONY AC-E90A Owner's Manual	SONY AC-E45A Owner's Manual
SONY 16229172 Service Manual	SONY 16180026 Service Manual	SONY 1400 Service Manual

Click to see text excerpt from the manual

1-1. OXF-CP3048/OXF-CP3024
. Setting of the display size and so on.
(3) Disconnect the harness from the connector (DIN, 8Pin) on the X terminal board (XP-200).
(4) Connect the unique keyboard (TEKTRONIX ACK-200) to the keyboard connector (the lower
connector of the two lines of the DIN 8-pin connectors) of the X terminal board (XP-200).
(5) Connect the harness to the connector (DIN, 8Pin) which have been disconnected.
(6) Input Enter from the keyboard (TEKTRONIX ACK-200) (press the Enter key).
Perform the following setting procedures. The setting procedure depends on whether the prompt is
displayed or not when inputting Enter.
1) When the prompt BOOT> is displayed
Input the following command from the keyboard (TEKTRONIX ACK-200)
BOOT> selftest monset 43 (Enter)
After the command is input, the display disappears once on the screen, and appears again with
the correct screen size.
2) When the prompt BOOT> is not displayed
Then input OEnterÃ�. Whenever OEnterÃ� is input, the display setting keeps changing. Press
OEnterÃ� until the setting becomes O43Ã� and the correct screen size is displayed.
When the correct screen size is displayed, press the F1 key of the keyboard (TEKTRONIX ACK-
200) to set.
(This memorizes the above setting in the internal memory of the X terminal board.)
(7) After settings have been finished, disconnect the keyboard (TEKTRONIX ACK-200).
(8) Connect the cable which have been disconnected to the connector Ether 0 on the rear panel.
Change the /etc/bootptab of the host computer.
(9) Checking of BOOT
Turn OFF the POWER of the control panel (OXF-CP3048/OXF-CP3024) once, and then turn ON the
POWER.
After a while, check that the OXÃ� mark is displayed on each LCD display.
OXF-R31-15(E)
OXF-R3/24