DCR-TRV60/TRV60E/TRV70
3-1-2. Precautions on AdjustingNote2: Setting the OForced VTR Power ON� mode (VTR mode)
Note1: Before performing the adjustments, check the data of page: 0,1) Select page: 0, address: 01, and set data: 01.
address: 10 is O00�. If not, set data: 00 to this address.2) Select page: D, address: 10, set data: 02, and press the PAUSE
1) The adjustments of this unit are performed in the VTR modebutton of the adjusting remote commander.
or camera mode.The above procedure will enable the VTR power to be turned
on with the control switch block (FK-4110 block) removed.
To set to the VTR mode, set the poOVCRwer s� or setwitch to After completing adjustments, be sure to eOForced Poxit the wer
the OForced VTR Power ON mode� using the adjusting remote
ON mode�.
commander (Note2).Note3: Setting the OForced Camera Power ON� mode (Camera mode)
To set to the Camera mode, set the poOCAMERAwer s�witch to 1) Select page: 0, address: 01, and set data: 01.
or set the OForced Camera Power ON mode� using the adjusting2) Select page: D, address: 10, set data: 01, and press the PAUSE
remote commander (Note3).button of the adjusting remote commander.
After completing adjustments, be surOFore to eced VTRxit the The above procedure will enable the camera power to be turned
Power ON Mode� or OForced Camera Power ON Mode�.on with the control switch block (FK-4110 block) removed.
After completing adjustments, be sure to eOForced Poxit the wer
(Note5)ON mode�.
2) Cabinet (R) (CK-130 board, LCD block) need not be connected.
Note4: Setting the OForced Memory Power ON� mode (Memory mode)
To remove it, disconnect the following connector.1) Select page: 0, address: 01, and set data: 01.
VC-314 board CN1007 (39P, 0.3mm)2) Select page: D, address: 10, set data: 05, and press the PAUSE
3) Short-circuit between (+) and (�) terminal of the capacitorbutton of the adjusting remote commander.
(C001) of the flash unit (FL4110) with the short jig about 10The above procedure will enable the memory power to be turned
seconds and discharge the capacitorOSER. (Refer to VICEon with the control switch block (FK-4110 block) removed.
NOTE �.)After completing adjustments, be sure to eOForced Poxit the wer
ON mode�.
4) The battery terminal is need not be connected. To remove it,Note5: Exiting the OForced Power ON� mode
disconnect the following connector.
1) Select page: 0, address: 01, and set data: 01.
DI-088 board CN4202 (3P, 1.5mm)2) Select page: D, address: 10, set data: 00, and press the PAUSE
5) The EVF block (LB-086 board) is need not be connected. button of the adjusting rToemote commander.
remove it, disconnect the following connector.3) Select page: 0, address: 01, and set data: 00.
DI-088 board CN3201 (16P, 0.5mm)
6) The flash unit (FL4110) is need not be connected. To remove
it, disconnect the following connector.
DI-088 board CN4001 (39P, 0.3mm)
7) The intelligent accessory shoe is need not be connected. To
remove it, disconnect the following connector.
DI-088 board CN4002 (10P, 0.5mm)
8) Removing the DI-088 board means removing the lithium 3V
power supply (DI-088 board, BT4001), data such as date, time,
user-set menus will be lost. After completing adjustments, reset
these data.
But, the self-diagnosis data and the data on history of use (total
drum rotation time etc.) will be kept even if the DI-088 board
has been removed. (Refer to O6-4.Service Mode� for the data
on the history use and the self-diagnosis data.)
To open the DI-088 board, use the following extension cable
between the DI-088 board CN4003 and VC-314 board CN1003.
J-6082-352-A (100P, 0.5mm)
9) By setting the OForced VTR Power ON mode�, the video section
can be operate even if the control switch block (FK-4110) has
been removed. When removing it, disconnect the following
connector.
VC-314 board CN1006 (27P, 0.3mm)
10) The JK-245 board (DV jack, USB jack) is need not be
connected. To remove it, disconnect the following connectors.
VC-314 board CN1002 (14P, 0.5mm)
11) The microphone unit is need not be connected. To remove it,
disconnect the following connectors.
VC-314 board CN1001 (4P, 1.0mm)
12) As the timing generator (IC7501) is provided on the CD-433
board of the lens block, the CN1101 of CD-433 board and
CN1500 of VC-314 board must be connected when performing
adjustments.
6-50 |
ACEC
