HCD-C700/C900
0. Disc Check MemoryDisc Type
1. Disc Type Auto Check
Disc Check2. DVD SL12 cm
3. DVD DL12 cm
4. CD12cm
5. LCD12 cm
1. SL Disc Check6. DVD SL8 cm
2. CD Disc Check7. DVD DL8 cm
3. DL Disc Check8. CD8 cm
9. LCD8 cm
0. Reset SLED TILT
TC. : : EMG. 00
0. Reset SLED TILTCD 12 cm
_
Display when CD 12cm disc was selected
On this screen, the mirror time is measured to judge the disc and it[0]Reset SLED TILTReset the Sled and Tilt to initial position.
is written to the EEPROM. First load DVD SL disc and press [1],
next load CD disc and press [2], and finally load DVD DL disc and[1]Disk Type CheckJudge automatically the loaded disc. As
press [3].the judged result is displayed at the
The adjustment must be executed more than once after default databottom of screen, make sure that it is
were written. External vibration or shock to the player must not becorrect.
given. Reference value for DVD is from 10 to 20, and for CD, fromIf Disc Check Memory menu has not
28 to 4F.been executed after EEPROM default
Check that the value of CD is larger than that of DVD.setting, the disc type cannot be judged.
When those values are beyond a range perform this adjustment again.In this case, return to the initial menu
From this screen, you can go to another mode by pressing [NEXT]and make a check for three types of discs
or [PREV] key, but you cannot enter this mode from another mode.(SL, DL, CD).
You can enter this mode from the Operation Menu screen only.
[2] to [9]Select the loaded disc. The adjusted
1. Disc Typevalue is written to the address of selected
disc. No further entry is necessary if [1]
Disc Type
was selected.
1. Disc Type Auto Check
2. DVD SL12 cm
3. DVD DL12 cm2. Servo Control
4. CD12cm
5. LCD12 cmServo Control
6. DVD SL8 cm1. LDOff R.Sled FWD
2. SPOff L.Sled REV
7. DVD DL8 cm
8. CD8 cm3. FocusOff
9. LCD8 cm4. TRK.Off
5. SledOff
0. Reset SLED TILT
EMG. 006. CLVAOff
7. FCS. Srch Off
On this screen, select the disc type. To select the disc type, press the
0. Reset SLED TILT
number of the loaded disc. The selected disc type is displayed at theSA. SI. EMG. 00
bottom. Selecting [1] automatically selects and displays the disc
DVD SL 12 cm
type. In case of wrong displayODisc Check Memory, retry �. Also,
opening the tray causes the set disc type to be cleared. In this case,On this screen, the servo on/off control necessary for replay is
set the disc type again after loading.executed. Normally, turn on each servo from 1 sequentially and
In performing manual operation, the disc type must be set.when CLVA is turned on, the usual trace mode becomes active. In
Once the disc type has been selected, the sector address or timethe trace mode, DVD sector address or CD time code is displayed.
code display field will appear as shown below. This is not displayThese values areed where the spindle is not locked.
displayed when PLL is locked.The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.
Disc Type
1. Disc Type Auto Check
2. DVD SL12 cm
3. DVD DL12 cm
4. CD12cm
5. LCD12 cm
6. DVD SL8 cm
7. DVD DL8 cm
8. CD8 cm
9. LCD8 cm
0. Reset SLED TILT
SA. SI. EMG. 00
DVD SL 12 cm
Display when DVD SL 12cm disc was selected
25 |
ACEC
