HCD-FC8/FC9
0-2-4. Model Type1-1. DVD-SL (single layer)
Model name is displayed.Press the 1 key on the remote commander and insert a DVD single
layer disc following the message. Then the adjustment will be made
0-2-5. Regionthrough the steps below, then adjusted values will be written to the
Model destination code is displayed. (2 digits number)EEPROM.
0-3. EEPROM CheckDVD Single Layer Disc Adjustment Steps:
0-3-1. Sampling Check1. Sled tilt reset
EEPROM check at every 64 words.2. Disc check memory SL
It compares read data with write data of each address. When3. Wait 300 msec
there are discrepancies between two data, it displays error.4. Set disc type SL
5. LD on
0-3-2. Detail Check6. Spindle start
EEPROM check at every 1 word.7. Wait 1 sec
It compares read data with write data of each address. When8. Focus servo on 0
there are discrepancies between two data, it displays error.9. Auto track offset adjust
10. CLVA on
0-4. GP I/O Check11. Wait 500 msec
Pull up/down setting check of the DVD system processor (IC206)12. Tracking on
pin 150, 151 and 154 (for clock setting port).13. Wait 1 sec
14. Sled on
0-5. SD Bus Check15. Check CLV on
SD bus data check between DVD decoder (IC701) and D-RAM16. Auto LFO adjust
(IC706).17. Auto focus offset adjust
18. Auto tilt position adjust
0-6. Video Check19. Auto focus gain adjust
Output the color bars for video level adjustment.20. Auto focus offset adjust
21. EQ boost adjust
1. DRIVE AUTO ADJUSTMENT22. Auto loop filter offset adjust
On the Test Mode Menu screen, press the [1] key on the remote23. Auto track gain adjust
commander, and the Adjustment Menu will be displayed.Search Check
24. 32 track jump forward
## Drive Auto Adjustment ##25. 32 track jump reverse
Adjustment Menu26. 500 track jump forward
27. 500 track jump reverse
0. ALL28.All servo stop
1. DVD-SL29.EEP copy loop filter offset
2. CD
3. DVD-DL1-2. CD
Press the [2] key on the remote commander and insert a CD disc
following the message. Then the adjustment will be made through
the steps below, then adjusted values will be written to the EEPROM.
CD Adjustment Steps
Exit: RETURN1. Sled tilt rest
2. Disc check memory CD
3. Wait 500 msec
Normally, [10/0] is selected to adjust DVD (single layer), CD and4. Set disc type CD
DVD (dual layer) in this order. But, individual items can be adjusted5. LD on
for the case where adjustment is suspended due to an error. In this6. Spindle start
mode, the adjustment can be made easily through the operation7. Wait 500 msec
following the message displayed on the screen.8. Focus servo on 0
The disc used for adjustment must be the one specified for9. Auto track offset adjust
adjustment.10. CLVA on
11. Wait 500 msec
1-0. ALL12. Tracking on
Press the [10/0] key on the remote commander, and the servo set13. (TC display start)
data in EEPROM will be initialized. Then, 1. DVD-SL disc, 2. CD14. Wait 1 sec
disc and 3. DVD-DL disc are adjusted in this order.15. Jitter display start
Each time one disc was adjusted, it is ejected. Replace it with the16. Sled ON
specified disc following the message. You can finish the adjustment17. Check CLV on
by pressing the [RETURN] button on the remote commander.18. Auto loop filter offset adjust
19. Auto focus offset adjust
Note:During adjustment of each disc, the measurement for disc type judg-20. Auto focus gain adjust
ment is made. As automatic adjustment does not judge the disc21. Auto focus offset adjust
type unlike conventional models, take care not to insert wrong type22. EQ boost adjust
discs. Also, do not give a shock during adjustment.23. Auto LFO Adjust
28 |
ACEC
