If no picture appears on your screen
Step 2:Connect the power cord Selecting the on-screen menu
SetupY Check that the monitor is correctly connected to the computer.
With the monitor and computer switched off, first connect the Y If NO INPUT SIGNAL appears on the screen, confirm that language (LANGUAGE/
Before using your monitor, check that the following accessories power cord to the monitor, then connect it to a power outlet.your computerOs graphic board is completely seated in the INFORMATION)
are included in your carton:correct bus slot.
Y Power cord (1)Y If you are replacing an old monitor with this model and OUT English, French, German, Spanish, and Italian versions of the on-
Y Windows Monitor Information Disk (1)OF SCAN RANGE appears on the screen, reconnect the old
screen menus are available. The default setting is English.
Y Warranty card (1)monitor. Then adjust the computerOs graphic board so that the
Y Notes on cleaning the screenOs surface (1)horizontal frequency is between 30 � 70 kHz, and the vertical
1Press the MENU button.
Y This instruction manual (1)frequency is between 48 � 120 Hz.
See page 9 for more information on using the MENU button.
For more information about the on-screen messages, see OTrouble CONTRAST/BRIGHTNE SSMENUEXIT
Step 1:Connect your monitor to symptoms and remedies� on page 14.H-SIZE/CENTER
MENUV-SIZE/CENTER
your computerpower cord (supplied)to AC INPIN/PIN BALANCEKEY/KEY BALANCE
bROTATION
For customers using Windows 95/98ENTERZOOM
Turn off the monitor and computer before connecting.COLOR
to a power outletTo maximize the potential of your monitor, install the new model RESET
information file from the supplied Windows Monitor Information Disk LANGUAGE/ INFORMAT INO
xConnecting to an IBM PC/AT or compatible onto your PC.DEGAUSS/CANCEL MOEIR
computerThis monitor complies with the OVESA DDC� Plug & Play standard. If
your PC/graphics board complies with DDC, select OPlug & Play Monitor 2Press the +/- buttons to highlight LANGUAGE/
(VESA DDC)� or this monitorOs model name as the monitor type in the
Step 3:Turn on the monitor and INFORMATION and press the ENTER button.
OControl Panel� of Windows 95/98. If your PC/graphics board has
See page 9 for more information on using the +/- and ENTER
computerdifficulty communicating with this monitor, load the Windows Monitor buttons.
Information Disk and select this monitorOs model name as the monitor
First turn on the monitor, then turn on the computer.type.
MENULANGUAGE/ INFORMATION
ENGLISHFRAN?AIS
For customers using Windows NT4.0ENTERbDEUT SCHITALIANOESPA?OLUS
Monitor setup in Windows NT4.0 is different from Windows 95/98 and
does not involve the selection of monitor type. Refer to the Windows SELECTEXIT
NT4.0 instruction manual for further details on adjusting the resolution,
to video outputThe installation of your monitor is complete.refresh rate, and number of colors.
If necessary, use the monitorOs controls to adjust the picture.3Press the ENTER button to select (LANGUAGE)
and press +/- buttons to select a language.
Adjusting the monitorOs resolution and color number
1-2Y ENGLISH
IBM PC/AT or Adjust the monitorOs resolution and color number by referring to your
compatible computercomputerOs instruction manual. The color number may vary according to Y FRAN?AIS: French
your computer or video board. The color palette setting and the actual Y DEUTSCH: German
number of colors are as follows:Y ESPA?OL: Spanish
Y High Color (16 bit) t 65,536 colorsY ITALIANO: Italian
xConnecting to a Macintosh or compatible Y True Color (24 bit) t about 16.77 million colors
computer In true color mode (24 bit), speed may be slower.To close the menu
Press the MENU button once to return to the main menu, and twice to
You will need a Macintosh adapter (not supplied).return to normal viewing. If no buttons are pressed, the menu closes
automatically after about 30 seconds.
To reset to English
See OResetting the adjustments (RESET)� on page 12.
Macintosh adapter
(not supplied)
Macintosh or to video
compatible computeroutput
67 |
ACEC
