The operating instructions mentioned here are partial abstracts
SECTION 1from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remein as in the manual.
GENERAL
Use of the tilt-swivel
PrecautionsIdentifying parts and controls
This monitor can be adjusted within the angles shown below. To
turn the monitor vertically or horizontally, hold it at the bottom
Warning on power connectionswith both hands.See the pages in parentheses for further details.
Y Use the supplied power cord. If you use a different power cord, FrontRear
be sure that it is compatible with your local power supply.
For the customers in the U.S.A.90u
If you do not use the appropriate cord, this monitor will not
conform to mandatory FCC standards.15u
90u
Example of plug types
5uMENU
ENTER
for 100 to 120 V ACfor 200 to 240 V AC
Y Before disconnecting the power cord, wait at least 30 seconds
after turning off the power to allow the static electricity on the
screenOs surface to discharge.
Y After the power is turned on, the screen is demagnetized
(degaussed) for about 5 seconds. This generates a strong
magnetic field around the screen which may affect data stored
on magnetic tapes and disks placed near the monitor. Be sure to 1 MENU button (page 9) 5AC IN connector (page 6)
This button displays the MENU OSD. This connector provides AC power to the monitor.
keep magnetic recording equipment, tapes, and disks away
1-1from the monitor.
2 ENTER button (page 9) 6Video input connector (HD15) (page 6)
This button selects the menu and adjustment items. This connector inputs RGB video signals (0.700 Vp-p,
The equipment should be installed near an easily accessible USpositive) and sync signals.
outlet.
3 6 (contrast) +/- buttons (page 9)
These buttons display the CONTRAST/BRIGHTNESS menu 1 2 3 4 5
Installation and function as the +/- buttons when adjusting other items.
6 7 89 10
Do not install the monitor in the following places:11 12 13 14 15
Y on surfaces (rugs, blankets, etc.) or near materials (curtains, 4 1 (power) switch and indicator (pages 6, 13, 16)
draperies, etc.) that may block the ventilation holesThis button turns the monitor on and off. The power indicator
Y near heat sources such as radiators or air ducts, or in a place lights up in green when the monitor is turned on, and either Pin No.Signal
subject to direct sunlightflashes in green and orange, or lights up in orange when the
Y in a place subject to severe temperature changesmonitor is in power saving mode.1Red
Y in a place subject to mechanical vibration or shock2Green
Y on an unstable surface
3Blue
Y near equipment which generates magnetism, such as a
transformer or high voltage power lines4ID (Ground)
Y near or on an electrically charged metal surface5DDC Ground*
6Red Ground
Maintenance
Y Clean the screen with a soft cloth. If you use a glass cleaning 7Green Ground
liquid, do not use any type of cleaner containing an anti-static 8Blue Ground
solution or similar additive as this may scratch the screenOs
9�
coating.
Y Do not rub, touch, or tap the surface of the screen with sharp or 10Ground
abrasive items such as a ballpoint pen or screwdriver. This type 11ID (Ground)
of contact may result in a scratched picture tube.
12Bi-Directional Data (SDA)*
Y Clean the cabinet, panel and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type 13H. Sync
of abrasive pad, scouring powder or solvent, such as alcohol or 14V. Sync
benzene.
15Data Clock (SCL)*
Transportation
* DDC (Display Data Channel) is a standard of VESA.
When you transport this monitor for repair or shipment, use the
original carton and packing materials.
45 |
ACEC
