CPD-200ES
The operating instructions mentioned here are partial abstracts from the Operating InstructionSECTION 1
Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
GENERAL
Getting StartedUsing Your MonitorAdjustments
Before using this monitor, please make sure that the followingWhen one of the preset-type signals is input, no picturep Before adjusting the items, turn on the unit and feed the
items are included in your package: Multiscan 100ES/200ESPreset and User Modesadjustment is necessary.video signal from the connected computer/work station.
You can, however, adjust the picture to your preferences by
monitor (1), power cord (1), warranty card (1), "Windows95following the procedure described below.p Adjustments will be stored automatically.
Monitor Information Disk" (1), and this operating instructionYou can adjust all items on the OSD (On Screen Display).
The Multiscan 100ES/200ES has factory preset modes for the 8 most
manual (1).
popular industry standards for true Oplug and play� capability.This monitor will sync with any IBM or compatible systemControl Panel
For less common modes, the Multiscan 100ES/200ESOs Digital
equipped with VGA or greater graphics capability. Although
Multiscan Technology will perform all of the complex adjustments
this monitor will sync to other platforms running at horizontalnecessary to ensure a high quality picture for any timing between
frequencies between 30 and 70 kHz, including Macintosh and30 and 70E kHz.
RESETCOLORGEOMSIZECENTER
Power Macintosh system, a cable adapter is required. Please
consult your dealer for advice on which adapter is suitable forCPD-100ES/100EST and CPD-200ES/200EST
your needs.No.Resolution HorizontalVerticalGraphics
(dots ´ lines) FrequencyFrequency Mode
Step 1:With the computer switched off, attach the video
signal cable to the video output.1640 ´ 48031.5 kHz60 HzVGA Graphic 1)Adjusting the Picture ContrastAdjusting the Picture Centering
2640 ´ 48043.3 kHz85 HzVESA 2)
3800 ´ 60046.9 kHz75 HzVESA 2)The adjustment data becomes the common setting for all inputThe adjustment data becomes the individual setting for each
4800 ´ 60053.7 kHz85 HzVESA2)signals.input signal received.
5832 ´ 62449.7 kHz75 HzMacintosh1Press the > ?// button.1Press the CENTER button.
16" Color 2)The OBRIGHTNESS/CONTRAST� OSD appears.The OCENTER� OSD appears.
IBM or compatible2)
61024 ´ 76860.0 kHz75 HzVESA
computerCENTER
to video output71024 ´ 76868.7 kHz85 HzVESA 2)BRIGHTNESS/CONTRASTCENTER
81280 ´ 1024 64.0 kHz60 HzVESA 2)
100503268
For the customers using the Windows¨4)95
N 4 NInstall the new model information of the Sony computer display31.5kHz/70Hz
Apple computer
from OWindows95 Monitor Information Disk� into your PC. (To2For vertical adjustment
to video outputinstall the file, refer to the attached OAbout the Windows95 MonitorPress the ? >/. buttons.
Information Disk/File�.)Horizontal Vertical
frequency* frequency*
Macintosh adapter (not supplied)This monitor complies with OVESA DDC�, the standards of
2Press the > ?// buttons to adjust picture contrast.
Step 2:Attach the power cord to the monitor and the otherPlug&Play. If your PC/graphic board complies with DDC,/ . . . for more contrast
end to a power outlet.select OPlug and Play Monitor (VESA DDC)� or this
? . . . for less contrast
monitorOs model name (CPD-100ES/100EST or CPD-200ES/
200EST) as OMonitor type� from OControl Panel� onThe OBRIGHTNESS/CONTRAST� OSD disappears 3 seconds
Windows95. Some PC/graphic boards do not comply withafter you release the buttons.> . . . to move up
DDC. Even if they comply with DDC, they may have some. . . . to move down
problems on connecting to this monitor. In this case, selectTo reset, press the RESET button while the OSD is on.
Power cord (supplied)this monitorOs model name (CPD-100ES/100EST or CPD-For horizontal adjustment
200ES/200EST) as OMonitor type� on Windows95.Press the > ?// buttons.
to a power outletAdjusting the Picture Brightness
Recommended horizontal timing conditions
Horizontal sync width should be: >1.0 ?sec.
The adjustment data becomes the common setting for all input
Horizontal blanking width should be: >3.6 ?sec. (Multiscan 100ES)/
Step 3:Turn on the monitor and computer.>3.0 ?sec. (Multiscan 200ES).signals.
Step 4:If necessary, adjust the user controls according toVertical sync width should be: < 560 ?sec.1Press the ? >/. button.
your personal preference.
NoteThe OBRIGHTNESS/CONTRAST� OSD appears.? . . . to move left
The installation of your Multiscan 100ES/200ES is complete.CPD-100ES/100EST and CPD-200ES/200EST does not apply to/ . . . to move right
Enjoy your monitor.Macintosh 21" color mode.BRIGHTNESS/CONTRAST
To erase the OCENTER� OSD, press the CENTER button
1) VGA is a trademark of IBM Corporation.again.
2) VESA is a trademark of the non-profit organization, Video10050The OCENTER� OSD automatically disappears 10 seconds after
Electronics Standard Association.you release the buttons.
3) Macintosh is a trademark of Apple Computer Inc.31.5kHz/70Hz
4) Windows¨ is a registered trademark of MicrosoftTo reset, press the RESET button while the OSD is on.
Corporation in the United States and other countries.
HorizontalVertical
frequency*frequency*
2Press the ? >/. buttons to adjust picture brightness.
. . . . for less brightness
> . . . for more brightness
*The horizontal and vertical frequencies for each input signal
The OBRIGHTNESS/CONTRAST� OSD disappears 3 secondsreceived appear on the OBRIGHTNESS/CONTRAST� OSD.
after you release the buttons.
To reset, press the RESET button while the OSD is on.
45 |
ACEC
