Additional settings (DEGAUSS/Resetting the adjustments (RESET)
Technical FeaturesTroubleshooting
CANCEL MOIRE)This monitor has the following two reset methods. Use the
RESET menu to reset the adjustments.Before contacting technical support, refer to this section.
You can manually degauss (demagnetize) the screen, and cancel
the moire.Preset and user modes
1Press the MENU button.
The main MENU appears on the screen.When the monitor receives an input signal, it automatically If thin lines appear on your screen
1Press the MENU button.
matches the signal to one of the factory preset modes stored in the
The main MENU appears on the screen.(damper wires)
2Press the +/- buttons to highlight 0 RESET and monitorOs memory to provide a high quality picture at the center
press the ENTER button.of the screen. (See Appendix for a list of the factory preset The lines you are experiencing on your screen are normal for the
2Press the +/- buttons to highlight DEGAUSS/
The RESET menu appears on the screen.modes.) For input signals that do not match one of the factory Trinitron monitor and are not a malfunction. These are shadows
CANCEL MOIRE and press the ENTER button.
Reset the settings according to the following instructions.preset modes, the digital Multiscan technology of this monitor from the damper wires used to stabilize the aperture grille and are
The DEGAUSS/CANCEL MOIRE menu appears on the
ensures that a clear picture appears on the screen for any timing in most noticeable when the screenOs background is light (usually
screen.Resetting all of the adjustment data for the
the monitorOs frequency range (horizontal: 30 � 70 kHz, vertical: white). The aperture grille is the essential element that makes a
current input signal (MODE)48 � 120 Hz) . If the picture is adjusted, the adjustment data is Trinitron picture tube unique by allowing more light to reach the
3Press the ENTER button to select the desired
adjustment item.Press the - button. stored as a user mode and automatically recalled whenever the screen, resulting in a brighter, more detailed picture.
Adjust the selected item according to the following The MODE item is selected. All of the adjustment data for the same input signal is received.
instructions.current input signal is reset. Note for Windows usersDamper wires
Note that the following items are not reset by this method:
Degaussing the screenY on-screen menu language (page 7)For Windows users, check your video board manual or the utility
Y pictureOs rotation (page 11)program which comes with your graphic board and select the
The monitor is automatically demagnetized when the power is
highest available refresh rate to maximize monitor performance.
turned on.
To manually degauss the monitor, first press the Resetting all of the adjustment data to factory
ENTER button to select (DEGAUSS). Then press the Power saving function
preset levels (ALL)
+ button.
The screen is degaussed for about 5 seconds. If a second degauss Press the + button. This monitor meets the power-saving guidelines set by VESA, On-screen messages
cycle is needed, allow a minimum interval of 20 minutes for the The ALL item is selected. With the exception of the USER USENERGY STAR, and NUTEK. If the monitor is connected to a
best result.settings in the COLOR menu, all of the adjustment data for all computer or video graphics board that is DPMS (Display Power If there is something wrong with the input signal, one of the
input signals is reset to the factory preset levels.following messages appears on the screen. To solve the problem,
Management Signaling) compliant, the monitor will
Cancelling the moireautomatically reduce power consumption in three stages as shown see OTrouble symptoms and remedies� on page 14.
Note
1-5If elliptical or wavy patterns appear on the screen, adjust the The monitorOs buttons will not operate for about 5 seconds when ALL is below.INFORMATION
moire cancellation level.selected.
To adjust the amount of moire cancellation, first press Power mode Power 1 (power) indicator
OUT OF SCAN RANGEInput signal condition
the ENTER button to select (CANCEL MOIRE). Then consumption
press the +/- buttons until the moire effect is at a normal L 110 Wgreen
minimum. operation(CPD-210GS)
*Moire is a type of natural interference which produces soft, wavy lines The input signal conditionL 105 W
(CPD-110GS)
on your screen. It may appear due to interference between the pattern OUT OF SCAN RANGE
of the picture on the screen and the phosphor pitch pattern of the 1 standbyL 15 Wgreen and orange indicates that the input signal is not supported by the
monitor.alternatemonitorOs specifications.
2 suspendL 15 Wgreen and orange NO INPUT SIGNAL
Example of moireindicates that no signal is being input to the monitor.
alternate
3 active off*L 5 Worange
power off0 Woff
* When your computer enters the Oactive off� mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After 20 seconds,
the monitor enters the power saving mode.
1213 |
ACEC
