CDX-L350/L450X/L470X
GeneralUS/Canadian/E model:
OutputsAudio output
Power amplifier control
lead (CDX-L350)CAUTION
Power antenna relayUse of controls or adjustments or performance of procedures
control lead (CDX-L350)
Power aerial relay controlother than those specified herein may result in hazardous
lead (CDX-L450X/L470X)radiation exposure.
Tone controlsBass ?10 dB at 20 Hz (CDX-L350)
Treble ?10 dB at 20 kHz (CDX-L350)
Bass ?9 dB at 100 Hz (L450X/L470X)If the optical pick-up block is defective, please replace the whole
Treble ?9 dB at 10 kHz (L450X/L470X)optical pick-up block.
Power requirements12 V DC car battery
Never turn the semi-fixed resistor located at the side of optical
(negative ground)
DimensionsApprox. 178 � 50 � 176 mmpick-up block.
(7 1/8 � 2 � 7 in.)
(w/h/d)
Mounting dimensionsApprox. 182 � 53 � 161 mmoptical pick-up bk loc
(7 1/4 � 2 1/8 � 6 3/8 in.)
(w/h/d)
MassApprox. 1.2 kg (2 lb. 10 oz.)
Supplied accessoriesParts for installation and
connections (1 set)
Front panel case (1)
Card remote commander
RM-X115 (CDX-L350/L470X)
Note (L450X/L470X)
This unit cannot be connected to a digital
preamplifier or an equalizer.
Design and specifications are subject to change without
notice.semi-fixed resistor
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCKAEP model:
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
This product is classified as a CLASS 1 LASER PRODUCT.
care.
This label is located on the bottom of the
chassis.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
" Never reuse a disconnected chip component.
" Notice that the minus side of a tantalum capacitor may be dam-This label is located on the drive unit's internal
aged by heat.chassis.
When replacing the chassis (T) of mechanism deck which have
the OCAUTION LABEL� attached, please be sure to put a new
CAUTION LABEL (3-223-913-11) to the chassis (T).
SAFETY-RELATED COMPONENT WARNING!!ATTENTION AU COMPOSANT AYANT RAPPORT
� LA S?CURIT?!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INLES COMPOSANTS IDENTIFI?S PAR UNE MARQUE 0 SUR LES
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.DIAGRAMMES SCH?MATIQUES ET LA LISTE DES PIéCES
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSESONT CRITIQUES POUR LA S?CURIT? DE FONCTIONNEMENT.
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORNE REMPLACER CES COMPOSANTS QUE PAR DES PIéCES
SONY DONT LES NUM?ROS SONT DONN?S DANS CE MANUEL
IN SUPPLEMENTS PUBLISHED BY SONY.
OU DANS LES SUPPL?MENTS PUBLI?S PAR SONY.
2 |
ACEC
