SONY CDX2180 Repair Manual

$7.99

SONY CDX2180 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Jacek Madej - 08/30/2008

Hi! love you!! schematics circuit best scan electronics area ...a have old radio grundig c8000 seek from net ... very done... hello best regard Edi from Poland

Patrick Guice - 04/23/2008

Phenomal manual great resoulution and very legible. Will become very helpfull in future for parts and service.

Jason Gaunt - 01/26/2008

This manual is for both the EU and Australian version of the CCD-TR55(E) Camcorder, as stated it includes both the users manual and the service manual. The quality of the manual is very good but it is only black and white (not full colour) and ultimately it is just a scan, so 4/5 from me.

Ernst-Guenter Hoffmann - 11/16/2007

Many thanks for the fast and easy delivery. When looking for a manual next time you will be my number one. Ernst, from good old Germany

Aaron Lawrence - 01/02/2008

Contains mechanism diagrams, parts lists and schematics for all worldwide versions of DC-X88Z. Also includes remote schematic etc. A few non-essential pages are missing such as specifications. Includes the mechanical and electronic calibration instructions for the tape decks.

Customers who bought this product also purchased

SONY SCPH-30000R Parts Catalog	SONY SCPH-39000 Parts Catalog	SONY SCPH-35000 Parts Catalog
SONY PLAY STATION 2 Parts Catalog	SONY 1401 Service Manual	SONY SCPH-50000 Parts Catalog

Click to see text excerpt from the manual

CD SECTIONFocus Gain Adjustment (Coarse adjustment)
This adjustment is not required unless the folloplaced:wing parts are re
Note:Y Optical pick-up
1. CD Block basically constructed to operate without adjustment.YRV4
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicaProcedure:ted.
3. Use the oscilloscope with more than 10 MW impedance.1. Set RV4 to the standard position. (mechanical center)
4. Clean an objective lens by an applicator with neutral deter2. Check whether operation noise (while noise type) caused bygent
when the signal level is low than specifalue with the folloied v wingthe 2-axis device (lens section of the optical pick-up) is
checks.abnormally loud.
If the operation noise is too loud, turn RV4 slightly counter-
Focus Bias Adjustmentclockwise.
Setting:This adjustment is performed with the set placedY If the gain is too low:
horizontally.Focus does not function and no music is selected.
Y If the gain is too high:
Noise caused by scratches and dust is heard and the operation
oscilloscope
becomes unstable.
SERVO board
Adjustment Location: servo board
TP (RF)+
TP (RF. GND)Ä�
Adjustment Location: servo board (component side)
Procedure:
1. Connect an oscilloscope between TP (RF) and TP (RF. GND)
on the SERVO board.
2. Connect the power supply.FOCUS GAIN ADJ
3. Push the RESET button (S881) on the DISPLAY board.RV4
IC3
4. Insert the disc (YEDS-18) and playback.
5. Adjust RV1 so that the oscilloscope waveform is clear and checkCN2
RF signal level is correct or not.
Note:Clear RF signal waveform means tha? t the sharp OÃ� can be
clearly distinguished at the center of the waveform.
RF signal waveform
VOLT/DIV: 200 mVIC1TP
TIME/DIV: 500 nS(RF. GND)
CN1
IC2
level: 1.0 Ä� 1.5 Vp-p
TP
Y When observing the eye pattern, set the oscilloscope to AC range(RF)
CN3
and raise the vertical sensitivity so that it may be easily seen.
Adjustment Location: servo board
RV1
FOCUS BIAS ADJ
Ä� 18 Ä�