SONY CDPS3 Repair Manual

$7.99

SONY CDPS3 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

vedat kaya - 07/18/2008

i got my service manual for philips vr685-02. Thanks a lot for my very clear and net service manual. I will continue shopping from user-manual.com.

Dutra Lacerda - 02/17/2008

All schematics for the Euro-PC and some extra info. Needed if you want to replace some missing hardware. A piece of great historical value and for vintage computing entusiasts.

Jeff Lewis - 07/24/2006

Received the Hitachi user manual. Happy happy happy! Thanks again.

Othmar Herbst - 01/13/2008

PDF contains : - schematics, but a little un-sharp. - disassembly instructions, accurate drawings - description of test-modes

Francisco Dorfman - 06/13/2007

I was thinking I will never find this manual. User-Manuals had saved my Teac V-7010 which is full of specific functions. Superfast service, excellent document. Thank you very much!

Customers who bought this product also purchased

SONY 362B Service Manual	SONY 6R-33 Service Manual	SONY 16229173 Service Manual
SONY 710BK-AL Service Manual	SONY 16229172 Service Manual	SONY 16180026 Service Manual

Click to see text excerpt from the manual

CDP-S3
6-10. IC PIN FUNCTION DESCRIPTION
" MAIN BOARD IC401 M30620MAA-B31FP (SYSTEM CONTROLLER)
Pin No.Pin NameI/ODescription
1 to 7NNNot used (open)
External data bus line byte selection signal input OLÃ�: 16 bits, OHÃ�: 8 bits
8BYTEI
Not used (fixed at OLÃ�)
9CNVSSNTo flash memory connector
10NNNot used (fixed at OLÃ�)
11NNNot used (open)
12RESETIReset signal input from the tuner unit (ST-S3/S5)
13X-OUTOSystem clock output terminal (16 MHz)
14VSSNGround terminal
15X-INISystem clock input terminal (16 MHz)
16VCCNPower supply terminal (+5V)
17NMIINon-maskable interrupt input terminal (fixed at OHÃ� in this set)
18NNNot used (open)
19SCORISubcode sync (S0+S1) detection signal input from the CXD3017Q (IC101)
20 to 23NNNot used (open)
24BU PWM 3ORFDC PWM signal output to the CXA2581N (IC103)
25NNNot used (open)
26BU PWM 2OTracking error PWM signal output to the CXA2581N (IC103)
27NNNot used (open)
28BU PWM 1OFocus error PWM signal output to the CXA2581N (IC103)
Communication data reading clock signal input or transfer clock signal output with the tuner unit
29IIC-CLKI/O
(ST-S3/S5)
30IIC-DATAI/O Communication data bus with the tuner system (ST-S3/S5)
31NNNot used
32SQ-DATA-INISubcode Q data input from the CXD3017Q (IC101)
33SQ-CLKOSubcode Q data reading clock signal output to the CXD3017Q (IC101)
34RTS1NNot used
35CD-DATAOCD decode data output to the CXD3017Q (IC101)
36SENSIInternal status (SENSE) signal input from the CXD3017Q (IC101)
37CD-CLKOSerial data transfer clock signal output to the CXD3017Q (IC101)
Power on/off control signal output for the CD mechanism deck section
38CD POWERO
OLÃ�: standby, OHÃ�: power on
39NNNot used (open)
40HOLDOAutomatic power control hold signal output to the CXA2581N (IC103)
41NNNot used (fixed at OLÃ�)
42XLTOSerial data latch pulse output to the CXD3017Q (IC101)
43XRSTOReset signal output to the CXD3017Q (IC101)
44LOAD-INOLoading motor drive signal (load-in direction) output the motor driver (IC701)
45LOAD-OUTOLoading motor drive signal (load-out direction) output the motor driver (IC701)
46OPENISub tray load in/out detect switch (S742) input OLÃ�: sub tray is chucking position
47CLOSEISub tray load in/out detect switch (S742) input OLÃ�: sub tray slides out of chucking position
Detection input from the disc tray 1 height sensor (IC731)
48T-SENS1I
OHÃ�: disc tray 1 position is chucking position
Detection input from the disc tray 2 height sensor (IC732)
49T-SENS2I
OHÃ�: disc tray 2 position is chucking position
24