SONY CDP-M205 Repair Manual

$7.99

SONY CDP-M205 - It's a complete service manual, and it's in PDF format. It contains circuit diagrams ( schemas ) etc. It also usually contains parts catalog. After placing order we'll send You download instructions on Your email address. See below for delivery information

The manual is available only in language(s): English

Link to manual will be sent on Your email address after You place order.

This product was added to our catalog on Monday 07 May, 2007.

Reviews

Write Review

Buy & Download

Product Reviews

There are currently no reviews for this product.

Other reviews

Nadia Yakunina - 06/19/2007

It was so difficult to find this manual on the internet - thanks a lot for making it so easy and simple. Incredibly handy. AND. It looks you make so many people happy for such small money. Good job!

Francisco Dorfman - 06/13/2007

I was thinking I will never find this manual. User-Manuals had saved my Teac V-7010 which is full of specific functions. Superfast service, excellent document. Thank you very much!

Jim Carrier - 08/02/2006

Outstanding and fast service! I received service manual in a moment after order. Thanks to this manual I can use my printer again!

Krzysztof Mazurek - 11/27/2007

Super ! Szukałem wszędzie i tutaj po 10 minutach miałem schemat w swoim PC.

Glen Meyer - 10/26/2008

Very fast service, manual is well scanned and clear, but the Appendix A containing PC Command table and Control codes are missing

Customers who bought this product also purchased

SONY 16229173 Service Manual	SONY 4300F Service Manual	SONY 7FA-70W Service Manual
SONY 6R-33 Service Manual	SONY 16180026 Service Manual	SONY 14DK1 Service Manual

Click to see text excerpt from the manual

Pin No.Pin nameI/ODescription.
41FIF I-V and E I-V amplifier inverted input.
42EIConnect these pins to photo diodes F and E.
I-V amplifier E gain adjustment
43EIÄ�
(When not using automatic balance adjustment) (not used).
44VEEÄ�Negative power supply.
Tracking error amplifier output
45TEOO
E-F signal is output.
Comparator input for balance adjustment
46LPFII
(Input from TEO through LPF).
47TEIITracking error input.
48ATSCIWindow comparator input for ATSC detection.
49TZCITrackig zero-cross comparator input.
50TDFCTICapacitor connection pin for defect time constant.
51VCO(VCC + VEE)/2 direct voltage output.
52FZCIFocus zero-cross comparator input.
IC103 DIGITAL SIGNAL PROCESSOR (CXD2529Q)
Pin No.Pin nameI/ODescription.
1VDDÄ�+5V power supply
2VSSÄ�Ground
3LMUTOLch OLÃ� detection flog (Not used)
4RMUTORch OLÃ� detection flog (Not used)
5ACDTOTest output (Not used)
6CKOUTOMaster clock divider output (Not used)
7SQCKIClock input for SQSO read out
8SQSOOSerial output for Sub-Q 80bit
9SENSOSENS signal output to CPU
10DATAISerial data input, supplied from CPU
11XLATILatch input, supplied from CPU
12CLOKISerial data transfer clock input, supplied from CPU
13SEINISENS input from IC101
14CNININumbers of track jump counted signal input
15DATOOSerial data output to IC101
16XLTOOSerial data latch output to IC101
17CLKOOSerial data transfer clock output to IC101
18SPOAIMicro computer demodulation interface (Input A)
19SPOBIMicro computer demodulation interface (Input B)
20SPOCIMicro computer demodulation interface (Input C)
21SPODIMicro computer demodulation interface (Input D)
22XLONOMicro computer demodulation interface (Output) (not used)
23FOKIFocus OK input
24VDDÄ�+5V power supply
25VSSÄ�Ground
26MONOOutput to control ON/OFF of spindle motor (Not used)
27MDPOOutput to control spindle motor servo
28MDSOOutput to control spindle motor servo (Not used)
29LOCKOGFS is sampled by 460Hz
30PWMIIInput to control the outside spindle motor
31TES0ITest pin (Connected to ground)
32TES1ITest pin (Connected to ground)
33VPCO2OCharge-pump output (Not used)
34VPCO1OCharge-pump output (Not used)
35VCKIIVCO2 oscillator input (Not used)
36V16MOVCO2 oscillator output (Not used)
Ä� 8 Ä�