4. Self-diagnosis Code Table
Self-diagnosis Code
BlockDetailedSymptom/StateCorrection
FunctionCode
Repaired by:
C 21 00 Condensation.Remove the cassette, and insert it again after one hour.
C 22 00 Video head is dirty.Clean with the optional cleaning cassette.
C 23 00 Non-standard battery is used.Use the InfoLITHIUM battery.
C 31 10Load the tape again, and perform operations from the beginning.LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
C 31 11Load the tape again, and perform operations from the beginning.complete within specified time
C 31 20 T reel side tape slacking when unloading.Load the tape again, and perform operations from the beginning.
C 31 21 S reel side tape slacking when unloading.Load the tape again, and perform operations from the beginning.
C 31 22 T reel faultLoad the tape again, and perform operations from the beginning.
C 31 23 S reel faultLoad the tape again, and perform operations from the beginning.
C 31 30 FG fault when starting capstanLoad the tape again, and perform operations from the beginning.
C 31 31 FG fault during normal capstan operLoad the taations pe again, and perform operations from the beginning.
C 31 40 FG fault when starting drum Load the tape again, and perform operations from the beginning.
C 31 41 PG fault when starting drum Load the tape again, and perform operations from the beginning.
C 31 42 FG fault during normal drum operLoad the taations pe again, and perform operations from the beginning.
C 31 43 PG fault during normal drum operLoad the taations pe again, and perform operations from the beginning.
C 31 44 Phase fault during normal drum operLoad the taations pe again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.C 32 10 LOAD direction loading motor time-out
UNLOAD direction loading motor time-Remove the battery or power cable, connect, and perform operations
outfrom the beginning.C3211
Remove the battery or power cable, connect, and perform operationsC 32 20 T reel side tape slacking when unloading.
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.C 32 21 S reel side tape slacking when unloading.
Remove the battery or power cable, connect, and perform operations
from the beginning.C 32 22 T reel fault
Remove the battery or power cable, connect, and perform operationsC 32 23 S reel fault
from the beginning.
Remove the battery or power cable, connect, and perform operationsC 32 30 FG fault when starting capstan
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.C 32 31 FG fault during normal capstan operations
Remove the battery or power cable, connect, and perform operations
C 32 40 FG fault when starting drum
from the beginning.
Remove the battery or power cable, connect, and perform operationsC 32 41 PG fault when starting drum
from the beginning.
Remove the battery or power cable, connect, and perform operations
from the beginning.C 32 42 FG fault during normal drum operations
Remove the battery or power cable, connect, and perform operations
C 32 43 PG fault during normal drum operations
from the beginning.
Remove the battery or power cable, connect, and perform operationsC 32 44 Phase fault during normal drum operations
from the beginning.
Inspect the lens block focus reset sensor (Pin !? of CN551 of VC-195
board) when focusing is performed when the focus dial is rotated in the
Difficult to adjust focusfocus manual mode and the focus motor drive circuit (IC552 of VC-195
(Cannot initialize focus.)board) when the focusing is not performed.E6100
Note : Use the remote commander RM-95 only for the model without
the focus dial.
Inspect the lens block zoom reset sensor (Pin @� of CN551 of VC-195
Zoom operations faultboard) when zooming is performed when the zoom lens is operated and
(Cannot initialize zoom lens.)the zoom motor drive circuit (IC552 of VC195 board) when zooming isE6110
not performed.
Inspect pitch angular velocity sensor (SE451 of SE-65 board) peripheralHandshake correction function does not
circuits.E 62 00 work well.(With pitch angular velocity
sensor output stopped)
Handshake correction function does not
Inspect yaw angular velocity sensor (SE452 of SE-65 board) peripheralE 62 01 work well.(With yaw angular velocity
circuits.sensor output stopped)
� 7 � |
ACEC
