1-4
Table of contensPrecautions
Chapter 1 Overview
E Setting the Power-Up Conditions and Data about the Screen
Chapter 2On safetyOn cleaning
Display N SYSTEM CONFIG Menu.................................... 39(E)
MenuYOperate the unit only with a power source asTo keep the unit looking brand-new, periodically clean
Overview .................................................................................39(E)Chapter 1 Overview
specified in OSpecifications� section. it with a mild detergent solution. Never use strong
Structure of the SYSTEM CONFIG Menu.............................40(E)
YThe nameplate indicating operating voltage, powersolvents such as thinner or benzine, or abrasive
Setting Lists of the SYSTEM CONFIG Menu........................40(E)cleansers since they will damage the cabinet. As a
consumption, etc., is located at the rear.
F Displaying Information About the MonitorYShould any solid object or liquid fall into the cabinet,safety precaution, unplug the unit before cleaning it.
N STATUS Menu ...................................................................unplug the unit and have it checked by qualified42(E)
Overview .................................................................................personnel before operating it any further.42(E)
Structure of the STATUS Menu..............................................YDo not drop or place heavy objects on the power42(E)On repacking
Setting Lists of the STATUS Menu ........................................cord. If the power cord is damaged, turn off the42(E)Do not throw away the carton and packing materials.
G Adjusting the Position, Size and Geometry of the Picturepower immediately. It is dangerous to use the unitThey make an ideal container which to transport the
N ALIGNMENT Menu..........................................................with a damaged power cord.43(E)unit.
Overview .................................................................................YUnplug the unit from the wall outlet if it is not to be43(E)If you have any questions about this unit, contact your
used for several days or more.authorized Sony dealer.
Structure of the ALIGNMENT Menu.....................................43(E)
YDisconnect the power cord from the AC outlet by
Setting Lists of the ALIGNMENT Menu ...............................43(E)
grasping the plug, not by pulling the cord.
Selecting the Monitor to Control N ADDRESS Menu............... 45(E)On magnetism
YThe socket-outlet shall be installed near the
Overview .................................................................................45(E)
equipment and shall be easily accessible.YDo not place the unit near any objects or pieces of
Displaying the ADDRESS Menu............................................YUse the supplied AC adaptor for the BVM-D9H1U/45(E)equipment which generate magnetism, such as
Cancelling the Remote Control Mode.....................................D9H1E/D9H1A/D9H5U/D9H5E/D9H5A models46(E)magnets, speakers, electric clocks, toys using
Exiting the ADDRESS Menu..................................................only. It is dangerous to use the AC adaptor for46(E)magnets, health appliances, etc. Magnetism will
Short-cut Function in the ADDRESS Menu ...........................models other than these.46(E)cause picture bounce, oscillations or picture
discoloration.
Specifications...................................................................................Y47(E)Also, the picture may become fuzzy or the colors
Chapter 3On installationmay not reproduce correctly due to earth magnetism.
Available Signal Format..........................................................53(E)
AppendixYAllow adequate air circulation to prevent internal heatThis depends on direction that the unit is installed.
Connection Cable Specifications
build-up.This is not equipment failure. In such a case, simply
for Color Temperature Probes..........................................54(E)
Do not place the unit on surfaces (rugs, blankets, etc.)degauss the unit.
Menu Index .....................................................................................56(E)
or near materials (curtains, draperies) that may block
Menu Configuration....................................................................... 58(E)
the ventilation holes.
YDo not install the unit in a location near heat sourcesOn the CRT
such as radiators or air ducts, or in a place subject toYDust accumulates on the CRT easily. Clean the CRT
direct sunlight, excessive dust, mechanical vibrationwhen necessary with a soft cloth.
or shock.The surface of the CRT is easily scratched; therefore,
do not rub or touch the surface of the CRT
unnecessarily since this may result in a scratched
On mounting the rackpicture tube.
When the monitor is mounted on the rack, theYIf you touch the surface of the CRT, you may feel a
proximity of other equipment or a decrease in airweak electrical shock. This is simply static electricity
circulation may cause heat to build up inside thethat is generated on the surface of the CRT. It will not
monitor. Therefore, when mounting the monitor onaffect the human body.
BVM-D9H1U/D9H5U/D9H1E/D9H5E/D9H1A/D9H5Athe rack, ensure there is an adequate opening for
ventilation or install a fan. The following operating
conditions are needed:On using as the monitor for 4:3 signals
Temperature: 0°C to 35°C (32°F to 95°F),The 16:9 mask is installed at the factory. When the
Optimum temperature: 20°C to 30°C (68°F to 86°F)display is set to the 4:3 aspect ratio, the upper and
lower portions of the display are masked and you
cannot view the upper and lower portions of the
On the battery (BVM-D9H1U/D9H1E/D9H1A/picture. Therefore, when you want to display the
D9H5U/D9H5E/D9H5A only)picture in 4:3 aspect ratio, install the supplied 4:3
The MAIN POWER switch is not supplied with themask.
above models. Therefore, when the power is turned
off with a battery installed, the monitor is set to
standby mode and a small amount of power is
consumed. When the monitor is not used for a long
period, remove the battery.
2 (E)3 (E) |