1-4
BKM-127W NTSC/PAL Input AdaptorBKM-127W NTSC/PAL Input Adaptor
The BKM-127W NTSC/PAL Input Adaptor is a videoAssigning input signals to connectorsSignal characteristics
Using the Input and Output
signal input adaptor for BVM-D9H/D14H series video
Connectors
monitors. When installed in an input option slot on theAnalog composite, YC signals
Before inputting signals to the BKM-127W, you must
rear panel of the video monitor, it provides video inputSignal level
For information about installing the BKM-127W in a videospecify the type and format of the signal that will be
and output connectors for the monitor and a decoderinput to each connector. To assign input signals toAnalog composite
monitor input option slot, see OInstalling into Video
for analog composite NTSC and PAL signals.Monitors� on page 11(E).each connector, use the on-screen INPUT CONFIG1 Vp-p +3 dB/�6 dB
menu of your video monitor.YCY: 1 Vp-p ?6 dB
C: 0.286 Vp-p ?6 dB (NTSC
Configuration of input/output connectors
FunctionsFor information about using the INPUT CONFIG menu,burst signal level)
and signals that may be inputrefer to the manual of your video monitor.0.3 Vp-p ?6 dB (PAL burst
signal level)
Decoder for analog composite NTSC/PALThe configuration of the input and output connectorsNoteLuminance signal
signalsand the signals that may be input are shown below.After assigning input signals to each connector, carryFrequency characteristics
Analog composite
out the AUTO adjustment of the CONTROL PRESET
The BKM-127W is equipped with decoders for analogADJ menu.Monochrome signal:
composite NTSC and PAL signals.ANALOG50 Hz to 6 MHz ?2 dB
1INAnalog composite signalsColor signal: �30 dB relative to
1subcarrier frequency
Analog input and output signal2OUTSpecificationsYCY: 50 Hz to 6 MHz ?2 dB
connectorsChrominance signals
3INDemodulation axis
Analog composite signals
The BKM-127W is equipped with two input and two2GeneralR�Y/B�Y
4
output connectors for analog signals and one input andOUTSubcarrier synchronization range
one output connectors for YC signals.Power requirements +5 V, ?6 V?200 Hz min.
Power consumption 3 WChroma phase adjustment range (NTSC)
5INYC?10! min.
Automatic termination (only terminals with3Operating conditions
6
the mark)OUTTemperature0!C to 35!C (32!F to 95!F)
Optimum temperatureAccessories supplied
The input connectors are terminated at 75 ohms inside,20!C to 30!C (68!F to 86!F)
when no cable is connected to the loop-through outputHumidity0% to 90% (no condensation)Installation Manual (1)
Pressure700 hPa to 1060 hPa
connectors. When a cable is connected to an output127W
connector, the 75-ohm termination is automatically
released.Storage and transport conditionsDesign and specifications are subject to change
Temperature�10!C to 40!C (14!F to 104!F)without notice.
Humidity0% to 90% (no condensation)
Input of analog composite signals
You can input analog composite signals to connectorsPressure700 hPa to 1060 hPa
Maximum external dimensions
1 and 3. When the cable is connected to connectors
2 and 4, the 75-ohm termination of connectors 125 ´ 162 ´ 122 mm
and 3 is automatically released and you can obtain(1 ´ 61/2 ´ 47/8 inches)
Mass270 g (10 oz)
the loop-through output from connectors 2 and 4.
Even if you do not wish to use loop-through output,
you need not attach the 75-ohm termination to
Input/output connectors
connectors 2 and 4.
Analog composite signals
Input of YC signals
BKM-120D/127W/129X/142HDBNC ´ 2, high impedance, with loop-through output
You can input YC signals to connector 5 and obtain
and 75-ohm automatic termination
loop-through output of the signals from connector 6.
Even if you do not wish to use loop-through output,
YC signals
you need not attach the 75-ohm termination to
4-pin mini DIN ´ 1, with loop-through output and 75-
connector 6.
ohm automatic termination
5 (E)6 (E) |
ACEC
