1-6
BKM-142HD HD SDI Input AdaptorBKM-142HD HD SDI Input Adaptor
The BKM-142HD HD SDI Input Adaptor is the videoAssigning input signals to connectorsSignal characteristics
Using the Input and Output
signal input adaptor for Sony BVM-D9H/D14H seriesBefore inputting signals to the BKM-142HD, you must
Connectors
video monitors.specify the type and format of the signal that will beDigital signals
When installed in the input option slots on the rearinput to each connector. To assign input signals toHD SDI signal input
For information about installing the BKM-142HD in the
panel of the video monitor, it provides video input/each connector, use the on-screen INPUT CONFIGNInput impedance 75 ohms, unbalanced
video monitor input option slots, see "Installing into Video
output connectors for the monitor and a decoder formenu of your video monitor.
Monitors" on page 11(E).Data rate1.4835Gbps to 1.485Gbps
HD serial digital signals.Conform to SMPTE 292M, BTA-S004B
For information about using the INPUT CONFIG menu,
MONITOR OUT
Configuration of input/output connectorsrefer to the manual of your video monitor.Output signal amplitude
and signals that may be input
Functions800 mVp-p?10%
NoteOutput impedance
The configuration of the input and output connectorsAfter assigning input signals to each connector, carry75 ohms, unbalanced
Decoding of HD serial digital signalsand the signals that may be input are shown below.out the AUTO adjustment of the CONTROL PRESETFrequency response
ADJ menu.Y48 Hz to 24 MHz ?3 dB
The built-in decoder decodes the HD serial digitalPB, PR48 Hz to 12 MHz ?3 dB
signals.Delay time error30 nsec max.
HD-SD1Transmission distance
Specifications
100 m (approx. 328 ft) max.,
HD serial digital input and output signalWhen using 5C-FB coaxial
connectors11INHD serial digital signalscables (Fujikura, Inc.) or
General
equivalent.
The BKM-142HD is equipped with two input
Power requirements +5 V, ?6 V
connectors for serial digital signals and one output
2 (supplied from the monitor)
connector for monitor signals.2INAccessory supplied
Power consumption 9W
Installation manual (1)
Operating conditions
Temperature0!C to 35!C (32!F to 95!F)
Design and specifications are subject to change
Optimum temperature
without notice.
3MONITORHD serial digital monitor20!C to 30!C (68!F to 86!F)
OUTsignalsHumidity0% to 90% (no condensation)
Pressure700 hPa to 1060 hPa
142HDStorage and transport conditions
Temperature�10!C to 40!C (14!F to 104!F)
Humidity0% to 90% (no condensation)
Pressure700 hPa to 1060 hPa
Input of HD serial digital signals
Maximum external dimensions (w/h/d)
You can input HD serial digital signals to connectors
50 ´ 162 ´ 122 mm
1 and 2. Input signals displayed on the video17
(2 ´ 6/2 ´ 4/8 inches)
monitor screen are output from connector 3. You
MassApprox. 730 g (1 lb 10 oz)
need not attach the 75-ohm termination to connector
3.
Input/output connectors
Notes
Y The MONITOR OUT signals are available onlyDigital input´BNC 2, with monitor output
BKM-120D/127W/129X/142HDwhen the power of the video monitor is ON. The
MONITOR OUT signals are not available when the
monitor is in standby mode.
Y The MONITOR OUT signals do not satisfy the ON-
LINE signal specifications.
9 (E)10 (E) |
ACEC
