The following settings should be checked after each ini-Vertical Symmetrv Set vertical symmetry (S-Correc-
tialization and, where necessary, set properly again:tion and Vertical Symmetry must be opti-
mized either way)
? Picture-size 4:3 or 16:9
Horizontal Pos. RGB Adjust horizontal image orienta-
? Picture-tube f.ex. A66EAK552X11
tion of a RGB source
By selection of picture tube the right geometry NVM
data is automatical fit (possible from Software MPHorizontal Position Adjust horizontal image position
2.0A upward).
Horizontal Amplitude Adjust image width
? VDSVirtual-DoIby-Suround On/OffCushion Compensate E/W-negative distortion
? TV-TypeB/G or multiTrapeze Set the vertical lines of the lest pattem
parallel to each other
? Tuner-Type6002 (Multi), 4046 (Multi),
4002 (BG) or 5002 (Multi)Corner Adjust vertical lines in the corners
? Front AVOn/OffHorizontal Symmetry Set horizontal symmetry
? ScartAnz.number of scart socketsBlanking Phase Left Adjust the scanning of the hori-
zontal rewind (left) (def. value 340)
? Funktionstasten 1-4 (number of F buttons on re-
mote control)Blanking Phase Right Adjust the scanning of the hori-
zontal rewind (right) (def. value 250)
? VTpagesnumber of teletext page memory
Chroma Delav Register Chroma-Signal with Luma-Signal
(100or500pages)
Luma Delav Register Luma-Signal with Chroma-
? ECO switchECO power switch On/Off
Signal. Note: Only one parameter (Chro-
ma or Luma Delay) needs to be balanced.
The following settings are also possible:
Newline Additional Option for changing the hori-
? SIeep Timer switch off after closedown On/Off
zontal image orientation. When balancing
? Forced PAL switch to ?enforced PAL? (only inthis parameter set odd numerical values
tuner playback mode)only.
(Def. value 61)
? Test mode - Data is only relevant for internal factory
production.DVCO The auxiliary colour carrier frequency
automatically adjusts to its reference
? Auto. formal On/Offvalue
For 16:9 units the effect of switching voltage or WSS
02 see G2 adjustment
conversion can be switched on or off.
Cutoff see black-white adjustment
? Kisi-Code global On
White Drive see black-white adjustment
? Kisi-Code reset if ?On" the code of childproof lock
is resetted
Note: The settings SVM G1 and SVM Delay are available
? Audio VCR mute Offfor the set Version Chassis TV 9.3 SVM only.
SVM G1 Set the definition äs best äs possible.
? Intl.-Data (VT) def.value 300
SVM Delav Set the definition to its maximum.
? OSD Brightness brightness of OSD
Kisi ruecksetzen The childproof lock can be reset
? OSD Contrast contrast of OSD
in various ways depending on the Soft-
? OSD Background color color of OSD backgroundware version (see ?Resetting the child-
proof lock?).
? OSD Foreground color color of OSD writing
Note: Following settings are only possible for set versions
Additional Service mode settings:
with Software MP2.xx.
This section is relevant for all set versions.
Vert. Pos OSD Adjust vertical OSD position.
Select the following service mode setting points with the
?A/V? buttonsHör. Pos OSD Adjust horizontal OSD position.
Adjust vertical OSD position in
Format Adjust viewing screen formalVert. Pos OSD MTSC)
NTSC-playback mode.
Vertical Amplitude Adjust vertical image height
Hör. Pos OSD MTSC)Adjust horizontal OSD position
Vertical Position Adjust vertical image position
in NTSC-playback mode.
S-Correction Adjust vertical linearity
Vert. Pos VT Adjust vertical position of teletext.
Hör. Pos VT Adjust horizontal position of teletext.
6 |
ACEC
